Ultra electronic Printer Latin Series User Manual

MAGICARD LATIN SERIES PRINTER  
INSTRUCTIONS FOR REPLACEMENT OF THE  
PRINTHEAD  
ASSEMBLY  
CAUTION – The following procedures involve contact with Electrostatic  
Sensitive Devices. All precautions for handling Electrostatic Sensitive Devices  
should be followed at all times, including the use of a grounded wrist strap.  
HOW TO USE THESE  
INSTRUCTIONS  
Your replacement printhead is despatched to you fully set up in the factory.  
All you are required to do is:  
1. Physically replace the printhead  
2. Adjust the Printhead density setting in the Magicard Support Tools.  
to the figure given on the enclosed test card.  
Full instruction to carry out both of these tasks are given in the following text:  
3506/07/01 Issue 1  
LATIN SERIES  
DCR No. 26759  
PRINTHEAD INSTALLATION & COMMISIONING  
 
Removal of the Unserviceable Printhead  
1. Ensure that the printer is switched off and disconnected from the mains  
supply.  
2. Release the door catch and lift open the door assembly.  
3. Locate and release the Quick Release Fastener on the Print head  
Assembly.  
3. Gently lift the printhead assembly forwards and downwards away from the  
lid  
assembly.  
4. Disconnect the electrical connector from the printhead.  
Installing the Replacement Printhead  
1. Ensure the printer is switched off and disconnected from the mains supply.  
2. Locate the lugs on the printhead assembly in the cutaway receptacles on  
the  
lid assembly. Gently move the printhead upwards and backwards into  
position.  
3. Secure the Quick Release Fastener attaching the Printhead to the lid.  
4. Reconnect the electrical connector to the printhead.  
Your printhead is now fitted. To complete the set up please turn to the  
next page.  
3506/07/01 Issue 1  
LATIN SERIES  
DCR No. 26759  
PRINTHEAD INSTALLATION & COMMISIONING  
 
Adjusting the Print Density  
To adjust the Print Density, ensure that there is power to the printer,  
the printer is connected to the computer and the printer is on line (Green light  
illuminated)  
CAUTION  
WHEN ADJUSTING THE PRINT DENSITY SETTING IT IS  
IMPORTANT TO NOTE THAT TOO HIGH A SETTING WILL CAUSE  
THE DYE FILM TO OVERHEAT AND ADHERE TO THE CARDS AN  
EXCESSIVELY HIGH SETTING WILL CAUSE THE DYE FILM TO  
MELT.  
1. Select the Magicard Support Tool Program from your computer  
menu.  
2. Using the drop down button on the Communications Window select  
the appropriate port.  
3. Using the Communications window refresh the data by selecting  
the Refresh Data button at the bottom of the window.  
4. Select configuration from the tabs at the top of the window.  
5. Move the Cursor to the Printhead Density Calibration box, click the  
mouse in the box and type in new setting  
6. Click the change button.  
The Printhead density has now been altered.  
Note:  
An increase in the number increases the intensity of the colour. As a  
datum point the setting should be reasonably close to the resistance setting  
shown on the printhead (example R3531) Because of the high numbers it is  
advisable to alter the settings in increments of 25 or 50.  
3506/07/01 Issue 1  
LATIN SERIES  
DCR No. 26759  
PRINTHEAD INSTALLATION & COMMISIONING  
 

Tekkeon Conference Phone ET6000 User Manual
Tektronix Sprinkler TDS500C User Manual
Toshiba Computer Drive MK5002MPL User Manual
Toshiba CRT Television 20AF43 User Manual
Toshiba Personal Computer TLCS 900 Family User Manual
Toshiba Telephone IP5000 Series User Manual
Tote Vision Computer Monitor LCD 840D User Manual
Tricity Bendix Dishwasher DH 090 User Manual
Tricity Bendix Freezer TB 117 FF User Manual
Universal Security Instruments Smoke Alarm MP117 User Manual